KEYENCE GT2 Dijital ölçüm probları

KEYENCE GT2 Doğrusal ölçüm probları
  • KEYENCE GT2 Cam cetvel ile mutlak konum ölçümü ile çalışan ölçüm probları yüksek çözünürlük ve yüksek doğrulukta ölçümler elde edilmesini sağlar. KEYENCE’in geliştirdiği scale shot system teknoloji sayesinde standart cam cetvelli problarda yaşanan referans noktasını unutma ve değer atlama gibi durumları yaşatmaz.
  • Cam cetvel üzerinde birbirinden farklı desenler kodlanmış durumdadır ve CMOS algılama sensörü ile bu desenler yüksek hızda taranarak mutlak konum elde edilir.
  • Ölçüm değerleri kaç defa ölçüm yapıldığından bağımsız olarak elde edilir.
  • Tekli kullanımda yükseklik, mesafe ve en yüksek veya en düşük mesafe değerleri elde etme gibi temel ölçümlerin yanında çoklu kullanımlarda kalınlık, genişlik, düzlemsellik, form gibi daha karmaşık ölçümleri sahip olduğu hesaplama fonksiyonları PLC’ye ihtiyaç duymadan yapabilmektedir.
Özellikler
  • 1mm’den başlayan ve 50mm’ye kadar değişen ölçüm stroklarına sahip problar
  • Yüksek doğruluk (1µ) ve yüksek tekrarlabilirlikte (0,1µ) ölçümler
  • 200 milyon gibi yüksek ölçüm ömrüne sahip problar
  • Mekanik ve havalı ölçüm prob alternatifleri
  • Temas edeceği malzeme yüzeyine göre uygun dokunma uçları ve seçilebilen baskı kuvvetli problar
  • IP67 korumu sınıfı sayesinde zorlu koşullarda kullanım
  • Tekli ve çoklu kullanımda hesaplanabilen matematiksel ölçümler
  • Ölçüm sonuçlarının harici cihazlara alınabilmesi için haberleşme protokol destekleri
  • Tüm ayarlamaların yapıldığı dijital amfi ünitesi
  • Zamanlama ve farklı ölçümler için hafıza fonksiyonları
  • Ölçeklendirilebilen analog çıkış ve ayarlanabilir dijital çıkışlar
Uygulama Alanları
  • Yükseklik ölçümü
  • Konum, pozisyon ölçümü
  • Kalınlık, genişlik, iç çap, dış çap ve boyut ölçümleri
  • Salgı, salınım, titreşim ölçümleri
  • Düzlük, düzlemsellik, form, bombe, iki yüzey arasındaki fark ölçümleri

Scale Shot System II

Ölçüm hatası yapmayan tamamen yepyeni bir algılama prensibi

Pozisyona göre cetvel üzerinde oluşturulmuş değişik şekilleri içeren mutlak değer skalası, yüksek hızlı ve yüksek çözünürlüklü CMOS sensörü ile yakalanır.
Dünyada bir ilk olan bu algılama prensibi, yüksek hızla hareket esnasında ölçüm hatası yapmadan sınıfındaki en yüksek doğruluğu temin eder.

Konvansiyel tip sensörlerdeki sorunlar

Skala (Darbe-Sayma) Metodu
Transormatör fark metodu
Scale Shot System II Teknolojisi

Bu yenilikçi sistem KEYENCE’in yeni geliştirdiği teknolojiye dayanır.
HL-LED’in yüksek yoğunluklu aydınlatması ışığı mutlak değer skalasından yüksek çözünürlüklü bir CMOS’a yansıtır. Çıkış sinyalleri, sürekli pozisyon tanıması yapan I-Processor tarafından hesaplanır. Hem de tüm bu özellikler 8-mm çapında ince bir gövdede mevcuttur.

Yağlı ortamlarda kullanılabilir

Dokümanlar

Keyence GT2 Genel Katalog
Keyence GT2 Kullanım Kılavuzu

Teknik özellikler

 

Model

GT2-100P

Mounting method

Panel mounting / Screw mounting with optional metal fittings

Output type

PNP output

Master unit / slave unit

Standard 2 ch, can be expanded up to 11 ch by adding an expansion board * 1

Power-supply voltage

DC 20-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

4,500 mW or less (30 V 150 mA or less)

Power saving (eco)

3,600 mW or less (30 V 120 mA or less) * 2

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output Applicable current 50 mA, maximum applicable voltage 30 V
ON residual voltage 1 V or less * NO / NC switchable
(when two or more sensor heads are connected in the GT2-100 series, the applicable current is 20 mA or less)

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 0.15 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET

Power / I / O cable

Power supply: Terminal block connection, input / output: 20-pole connector (MIL standard)

mass

About 380 g

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)
* 2 For GT2-100 series, when sensor heads are connected for the maximum number of connected units and all units are set to save power.

Model

GT2-71MCN

type

Analog connector type

Mounting method

DIN rail mounting

Output type

NPN output

Master unit / slave unit

Master unit * 1

Power-supply voltage

DC 20-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,700 mW or less (30 V 90 mA or less)

Power saving (eco)

2,200 mW or less (30 V 73.3 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

NPN open collector non-voltage output
Applicable current 50 mA, maximum applicable voltage 40 V ON residual voltage 1 V or less * NO / NC switchable (GT2-71MCN / 71MCP only HH, LL are not available)

Analog output

4 to 20 mA Maximum load resistance 350 Ω
Analog output range can be set arbitrarily

Response time

When using hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1,000 ms,
GT2-P ***: hsp (12 ms), 20 ms, 40 ms, 400 ms, 2,000 ms, 4,000 ms

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (-10 to + 45 ° C when only GT2-71MCN / 71MCP is added)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

mass

About 70 g

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-71MCP

type

Analog connector type

Mounting method

DIN rail mounting

Output type

PNP output

Master unit / slave unit

Master unit * 1

Power-supply voltage

DC 20-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,700 mW or less (30 V 90 mA or less)

Power saving (eco)

2,200 mW or less (30 V 73.3 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output
Applicable current 50 mA, maximum applicable voltage 30 V ON residual voltage 1 V or less * NO / NC switchable (GT2-71MCN / 71MCP only does not have HH or LL)

Analog output

4 to 20 mA Maximum load resistance 350 Ω
Analog output range can be set arbitrarily

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (-10 to + 45 ° C when adding GT2-71MCN / 71MCP only) (Do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

mass

About 70 g

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-71N

type

Standard loose wire type

Mounting method

DIN rail mounting

Output type

NPN output

Master unit / slave unit

Master unit * 1

Power-supply voltage

DC 10-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,200 mW or less (30 V 73.3 mA or less)

Power saving (eco)

1,700 mW or less (30 V 56.7 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

NPN open collector non-voltage output
Applicable current 50 mA, maximum applicable voltage 40 V ON residual voltage 1 V or less * NO / NC switchable (GT2-71MCN / 71MCP only, HH, LL are not available)

Analog output

Response time

When using hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1,000 ms,
GT2-P ***: hsp (12 ms), 20 ms, 40 ms, 400 ms, 2,000 ms, 4,000 ms

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (-10 to + 45 ° C when only GT2-71MCN / 71MCP is added)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

mass

Approximately 140 g (including power cable)

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-71P

type

Standard loose wire type

Mounting method

DIN rail mounting

Output type

PNP output

Master unit / slave unit

Master unit * 1

Power-supply voltage

DC 10-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,200 mW or less (30 V 73.3 mA or less)

Power saving (eco)

1,700 mW or less (30 V 56.7 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output
Applicable current 50 mA, maximum applicable voltage 30 V ON residual voltage 1 V or less * NO / NC switchable (GT2-71MCN / 71MCP only does not have HH or LL)

Analog output

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

mass

Approximately 140 g (including power cable)

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-72CP

type

Standard connector type

Mounting method

DIN rail mounting

Output type

PNP output

Master unit / slave unit

Slave unit * 1

Power-supply voltage

DC 10-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,200 mW or less (30 V 73.3 mA or less)

Power saving (eco)

1,700 mW or less (30 V 56.7 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output
Applicable current 50 mA, maximum applicable voltage 30 V ON residual voltage 1 V or less * NO / NC switchable (GT2-71MCN / 71MCP only does not have HH or LL)

Analog output

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

mass

About 70 g

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-72P

type

Standard loose wire type

Mounting method

DIN rail mounting

Output type

PNP output

Master unit / slave unit

Slave unit * 1

Power-supply voltage

DC 10-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,200 mW or less (30 V 73.3 mA or less)

Power saving (eco)

1,700 mW or less (30 V 56.7 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output
Applicable current 50 mA, maximum applicable voltage 30 V ON residual voltage 1 V or less * NO / NC switchable (GT2-71MCN / 71MCP only does not have HH or LL)

Analog output

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

mass

Approximately 140 g (including power cable)

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-75P

Mounting method

Panel mounting

Output type

PNP output

Master unit / slave unit

Master unit * 1

Power-supply voltage

DC 10-30 V Ripple (pp) 10% included Class2 * 1

power consumption

Normal

2,200 mW or less (30 V 73.3 mA or less)

Power saving (eco)

1,700 mW or less (30 V 56.7 mA or less)

Display method

Measured value display

6 + 1/2 digit 7-segment LED display (red)

Sub display

2-color 13-step bar LED display (red, green), various indicators (red, green)

Display range

-199.9999 ~ 199.9999

Display resolution

0.1 µm

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output Applicable current 50 mA, maximum applicable voltage 30 V
ON residual voltage 1 V or less * NO / NC switchable
(when two or more sensor heads are connected in the GT2-100 series, the applicable current is 20 mA or less)

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET, Cable: PVC

Power / I / O cable

12-core connector connection (connection cable included)

mass

Approximately 140 g (including panel fixture, front protective cover, power cable)

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)

Model

GT2-A12

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

1.2 N * 2

When installed sideways

1.1 N * 2

When installed facing up

1.0 N * 2

Sampling cycle

1 ms

Fluid used

Dry air

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC) * 3

Pressure resistance

1 MPa

Working pressure range

0.25 MPa to 0.50 MPa

Operating ambient temperature

0 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: Zinc die-cast, Cylinder part: Aluminum alloy, Air joint part Resin: Polyacetal, Air joint metal part: Brass nickel plating, Indicator light Polyallylate (PAR)

Dust boots

NBR

Contact

SUS304, SUS440C * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 145 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Connect the air tube to the exhaust fitting to prevent foreign matter from entering the inside through the fitting.
* 4 Contact is also available as an option sold separately.

Model

GT2-A12K

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.1 µm

Instruction accuracy

1 µm (PP) * 1

Measuring power

When installed facing down

1.2 N * 2

When installed sideways

1.1 N * 2

When installed facing up

1.0 N * 2

Sampling cycle

1 ms

Fluid used

Dry air

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC) * 3

Pressure resistance

1 MPa

Working pressure range

0.25 MPa to 0.50 MPa

Operating ambient temperature

0 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: Zinc die-cast, Cylinder part: Aluminum alloy, Air joint part Resin: Polyacetal, Air joint metal part: Brass nickel plating, Indicator light Polyallylate (PAR)

Dust boots

NBR

Contact

SUS304, Cemented Carbide Tungsten Alloy * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 145 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Connect the air tube to the exhaust fitting to prevent foreign matter from entering the inside through the fitting.
* 4 Contact is also available as an option sold separately.

Model

GT2-A12L

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

0.4 N * 2

When installed sideways

0.3 N * 2

When installed facing up

0.2 N * 2

Sampling cycle

1 ms

Fluid used

Dry air

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

Pressure resistance

1 MPa

Working pressure range

0.25 MPa to 0.50 MPa

Operating ambient temperature

0 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: Zinc die-cast, Cylinder part: Aluminum alloy, Air joint part Resin: Polyacetal, Air joint metal part: Brass nickel plating, Indicator light Polyallylate (PAR)

Dust boots

Contact

SUS304, SUS440C * 3

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 145 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Contact is also available as an option sold separately.

Model

GT2-A32

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

32 mm

resolution

0.5 µm

Instruction accuracy

3 µm (PP) * 1

Measuring power

When installed facing down

2.1 N * 2

When installed sideways

1.8 N * 2

When installed facing up

1.5 N * 2

Sampling cycle

1 ms

Fluid used

Dry air

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC) * 3

Pressure resistance

1 MPa

Working pressure range

0.25 MPa to 0.50 MPa

Operating ambient temperature

0 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10 to 55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction * 4

Material

Body

Body case: Zinc die-cast, Cylinder part: Aluminum alloy, Air joint part Resin: Polyacetal, Air joint metal part: Brass nickel plating, Indicator light Polyallylate (PAR)

Dust boots

NBR

Contact

SUS304, SUS440C * 5

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 340 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Connect the air tube to the exhaust fitting to prevent foreign matter from entering the inside through the fitting.
* 4 When using mounting bracket D (OP-84327), the double amplitude is 0.75 mm.
* 5 Contact is also available as an option sold separately.

Model

GT2-A50

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

50 mm

resolution

0.5 µm

Instruction accuracy

3.5 µm (PP) * 1

Measuring power

When installed facing down

3.2 N * 2

When installed sideways

2.8 N * 2

When installed facing up

2.4 N * 2

Sampling cycle

1 ms

Fluid used

Dry air

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC) * 3

Pressure resistance

1 MPa

Working pressure range

0.25 MPa to 0.50 MPa

Operating ambient temperature

0 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10 to 55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction * 4

Material

Body

Body case: Zinc die-cast, Cylinder part: Aluminum alloy, Air joint part Resin: Polyacetal, Air joint metal part: Brass nickel plating, Indicator light Polyallylate (PAR)

Dust boots

NBR

Contact

SUS304, SUS440C * 5

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 405 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Connect the air tube to the exhaust fitting to prevent foreign matter from entering the inside through the fitting.
* 4 When using mounting bracket D (OP-84327), the double amplitude is 0.75 mm.
* 5 Contact is also available as an option sold separately.

Model

GT2-E3P

Mounting method

Added to GT2-100N / 100P (up to 3)

Output type

PNP output

Master unit / slave unit

Slave unit (can be expanded arbitrarily from 1 to 3 ch) * 1

Power-supply voltage

Supplied from GT2-100N / 100P * 1

power consumption

Normal

4,200 mW or less (30 V 140 mA or less) * 2

Power saving (eco)

4,000 mW or less (30 V 133.3 mA or less)

Display method

Measured value display

Sub display

Display range

Display resolution

Sampling speed

1,000 times / sec

Control input

Timing / preset / reset / bank input

Non-voltage input (contact, non-contact), timing input: input time 2 ms or more, preset / reset / bank input: input time 20 ms or more

Control output

HH / High / GO / Low / LL

PNP open collector non-voltage output Applicable current 50 mA, maximum applicable voltage 30 V
ON residual voltage 1 V or less * NO / NC switchable
(when two or more sensor heads are connected in the GT2-100 series, the applicable current is 20 mA or less)

Response time

hsp (3 ms), 5 ms, 10 ms, 100 ms, 500 ms, 1 s

Environmental resistance

Operating ambient temperature

-10 to + 50 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body / cover: Polycarbonate, Key top: Polyacetal, Front sheet: PET

Power / I / O cable

Input / output: 30-pole connector (MIL standard)

mass

About 80 g

* 1 Precautions when adding and using the GT2-70 series (excluding GT2-71D)
You can add up to a total of 15 amplifiers, one master unit and 14 slave units. When using the DIN mounting type, be sure to mount it on the DIN rail (mounted on a metal plate), and when adding it, be sure to use the end unit (OP-26751). Also, when adding, please check the following specification restrictions according to the number of units to be added before using.
[Up to 8 units including the master unit] The
power supply voltage is DC 20-30 V. The applied current for each output should be 20 mA or less.
[From 9 to 15 units including the master unit] The
power supply voltage is DC 20-30 V. The residual voltage when ON is 1.5 V or less. The applied current for each output should be 10 mA or less. (Including the output current of DL-RB1A)
* 2 For GT2-100 series, when sensor heads are connected for the maximum number of connected units and all units are set to save power.

Model

GT2-H12

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

1.0 N * 2

When installed sideways

0.9 N * 2

When installed facing up

0.8 N * 2

Sampling cycle

1 ms

Mechanical responsiveness

10 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC)

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: Zinc die-cast, indicator light: Polyarylate (PAR)

Dust boots

NBR

Contact

SUS304, SUS440C * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 95 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 Contact is also available as an option sold separately.

Model

GT2-H12K

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.1 µm

Instruction accuracy

1 µm (PP) * 1

Measuring power

When installed facing down

1.0 N * 2

When installed sideways

0.9 N * 2

When installed facing up

0.8 N * 2

Sampling cycle

1 ms

Mechanical responsiveness

10 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC)

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: Zinc die-cast, indicator light: Polyarylate (PAR)

Dust boots

NBR

Contact

SUS304, Cemented Carbide Tungsten Alloy * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 95 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 Contact is also available as an option sold separately.

Model

GT2-H12L

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

0.4 N * 2

When installed sideways

0.3 N * 2

When installed facing up

0.2 N * 2

Sampling cycle

1 ms

Mechanical responsiveness

4 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: Zinc die-cast, indicator light: Polyarylate (PAR)

Dust boots

Contact

SUS304, SUS440C * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 95 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 Contact is also available as an option sold separately.

Model

GT2-H32

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

32 mm

resolution

0.5 µm

Instruction accuracy

3 µm (PP) * 1

Measuring power

When installed facing down

2.1 N * 2

When installed sideways

1.8 N * 2

When installed facing up

1.5 N * 2

Sampling cycle

1 ms

Mechanical responsiveness

6 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC)

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body

Body case: Zinc die-cast, indicator light: Polyarylate (PAR)

Dust boots

NBR

Contact

SUS304, SUS440C * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 270 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 Contact is also available as an option sold separately.

Model

GT2-H50

Detection method

Scale Shot System Absolute (No Value Jump) Type

Measurement range

50 mm

resolution

0.5 µm

Instruction accuracy

3.5 µm (PP) * 1

Measuring power

When installed facing down

3.2 N * 2

When installed sideways

2.8 N * 2

When installed facing up

2.4 N * 2

Sampling cycle

1 ms

Mechanical responsiveness

7 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC)

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

Body

Body case: Zinc die-cast, indicator light: Polyarylate (PAR)

Dust boots

NBR

Contact

SUS304, SUS440C * 4

Head cable

Sold separately (connected to M8 connector)

mass

Approximately 320 g (cable not included)

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 Contact is also available as an option sold separately.

Model

GT2-P12

Detection method

Scale Shot System II Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

1.0 N * 2

When installed sideways

0.95 N * 2

When installed facing up

0.9 N * 2

Sampling cycle

4 ms

Mechanical responsiveness

10 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protective structure

IP67G (JIS) * 4 , IP67 (IEC), NEMA Type 13 * 4

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: SUS303, Status indicator: PET, Sensor head-Cable between relay connectors: PUR,
Relay connector: PBT, Spindle of GT2-PA12K / PA12: SUS430 (fluorine-based coating),
Dust seal (GT2-PA12K / PA12) Dust seal): SUS303 / SUS304 / Aluminum (anodized) / Special polyester

Dust boots

NBR

Contact

SUS304, SUS440C * 5

Head cable

Sold separately (connected to relay connector)

mass

Approximately 35 g (cable not included) * 6

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 When using an M8 oil resistant cable (GT2-CHP2M / CHP5M / CHP10M) for the sensor head cable
* 5 Contact is also available as an option sold separately.
* 6 Includes relay connector.

Model

GT2-P12K

Detection method

Scale Shot System II Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.1 µm

Instruction accuracy

1 µm (PP) * 1

Measuring power

When installed facing down

1.0 N * 2

When installed sideways

0.95 N * 2

When installed facing up

0.9 N * 2

Sampling cycle

4 ms

Mechanical responsiveness

10 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protective structure

IP67G (JIS) * 4 , IP67 (IEC), NEMA Type 13 * 4

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: SUS303, Status indicator: PET, Sensor head-Cable between relay connectors: PUR,
Relay connector: PBT, Spindle of GT2-PA12K / PA12: SUS430 (fluorine-based coating),
Dust seal (GT2-PA12K / PA12) Dust seal): SUS303 / SUS304 / Aluminum (anodized) / Special polyester

Dust boots

NBR

Contact

SUS304, Cemented Carbide Tungsten Alloy * 5

Head cable

Sold separately (connected to relay connector)

mass

Approximately 35 g (cable not included) * 6

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 When using an M8 oil resistant cable (GT2-CHP2M / CHP5M / CHP10M) for the sensor head cable
* 5 Contact is also available as an option sold separately.
* 6 Includes relay connector.

Model

GT2-P12L

Detection method

Scale Shot System II Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

0.2 N * 2

When installed sideways

0.15 N * 2

When installed facing up

0.1 N * 2

Sampling cycle

4 ms

Mechanical responsiveness

4 Hz * 3

Operation indicator

2-color LED (red, green)

Environmental resistance

Protective structure

Operating ambient temperature

-10 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: SUS303, Status indicator: PET, Sensor head-Cable between relay connectors: PUR,
Relay connector: PBT, Spindle of GT2-PA12K / PA12: SUS430 (fluorine-based coating),
Dust seal (GT2-PA12K / PA12) Dust seal): SUS303 / SUS304 / Aluminum (anodized) / Special polyester

Dust boots

Contact

SUS304, SUS440C * 4

Head cable

Sold separately (connected to relay connector)

mass

Approximately 35 g (cable not included) * 5

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a representative value near the measurement center value. Please note that the measuring force changes depending on the mounting condition of the dust boots.
* 3 Value when the ambient temperature is 20 ° C.
* 4 Contact is also available as an option sold separately.
* 5 Includes relay connector.

Model

GT2-PA12

Detection method

Scale Shot System II Absolute (No Value Jump) Type

Measurement range

12 mm

resolution

0.5 µm

Instruction accuracy

2 µm (PP) * 1

Measuring power

When installed facing down

1.2 N * 2

When installed sideways

1.15 N * 2

When installed facing up

1.1 N * 2

Sampling cycle

4 ms

Fluid used

Clean dry air

Operation indicator

2-color LED (red, green)

Environmental resistance

Protection class

IP67 (IEC)

Pressure resistance

0.5 MPa

Working pressure range

0.24 to 0.26 MPa

Operating ambient temperature

0 to + 55 ° C (do not freeze)

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Impact resistance

1,000 m / s 2 (IEC60068-2-27)

Material

Body

Body case: SUS303, Status indicator: PET, Sensor head-Cable between relay connectors: PUR, Relay connector: PBT

Spindle part

SUS430 (Fluorine coating)
Dust seal: SUS303 / SUS304 / Aluminum (anodized) / Special polyester fiber

Contact

SUS304, SUS440C * 3

Head cable

Sold separately (connected to relay connector)

mass

Approximately 35 g (cable not included) * 4

* 1 Value for the entire measurement range and ambient temperature of 20 ° C.
* 2 This is a typical example when using 0.25 MPa. The measuring force changes depending on the air pressure used.
* 3 Contact is also available as an option sold separately.
* 4 Includes relay connector.

İnsanların web sitemizi nasıl kullandıklarını analiz ederek, deneyiminizi ve hizmetlerimizi daha iyi hale getirmek için kendi çerezlerimizi ve üçüncü taraf çerezleri kullanıyoruz. Web sitesini kullanmaya devam ettiğinizde bunların kullanımını kabul ettiğinizi anlıyoruz. Çerez Politikamız hakkında daha fazla bilgi için burayı tıklayın.