KEYENCE LK-G 5000 serisi hedefleri hatasız şekilde ölçer
KEYENCE LK-G 5000 sensörü, çok çeşitli uygulamalar için mükemmel performans sağlamak üzere sınıfının en iyisi hız ve doğruluğu dengelemek için lazer üçgensel ölçüm yönteminden faydalanır.

 

  • Dünyanın en hızlısı: 392kHz
  • Sınıfında en az hata oranı: ±0.02%
  • Sınıfında en fazla tekrarlanabilirlik: 0.005µm
  • Yeni geliştirilen “ABLE II” kumandası
  • Son teknoloji ile donatılmış küçük boyutlu sensör kafası
Özellikler

Lazer deplasman sensörleri hızlı, hatasız ve her türlü uygulamada mükemmel performans gösterebilecek kapasitede olmalıdır. Dünyanın en iyisi olmaya aday LK-G5000 en son teknoloji ile üretilmiştir

AKTİF DENGELİ ABLE II LAZER KUMANDA MOTORU

Lazer ışık yoğunluğunu en uygun seviyeye otomatik olarak ayarlar

 

Bilinen ABLE kumandası artık daha güçlü. Able II lazer emisyonun üç öğesi; zaman, lazer gücü ve kazanımı dengeleyerek RS-CMOS kapasitesini akıllıca optimize eder. Bunun da ötesinde, ABLE II geleneksel modellere göre sekiz kat daha hızlı izleme kapasitesine sahiptir.

 

[Yeni Geliştirilen] RS-CMOS R = YÜKSEK ÇÖZÜNÜRLÜK  S = YÜKSEK HIZ
LK-G5000 Serisine özel ultra yüksek tekrar okuma kapasitesine sahip yüksek hızlı CMOS sensör

“Yüksek hız” ve  “Yüksek çözünürlük” bir arada elde edilir. Çift portlu transfer sayesinde piksel veriler geleneksel modellere göre sekiz kat daha hızlı transfer edilebilir. Dörtlü hız saati sayesinde daha yüksek hızlar elde etmek mümkündür. Yeni geliştirilen HDE lens* ve iki kat yüksek çözünürlük sayesinde alınan ışık dalga modelleri elde etmek mümkün. KEYENCE zorlu uygulamalar için daha yüksek doğruluk ve tekrar okuma oranı sağlıyor.
*HDE lens=High Definition Ernostar lens

Geniş Hedefler

Geniş hedeflerle doğru ölçüm

Geniş Işın Tipi

Düz gibi görünen yüzeylere yakından bakıldığında genellikle küçük yansımalar ve çukurlar olduğu görülür. Bu mikroskobik pürüzler normal ışınlı sensörlerde genellikle ölçüm hatalarına neden olur. Geniş ışın ile birlikte kullanılan sensör başlığı sayesinde düzgün olmayan yüzeyler zorlu hedeflerin bile doğru şekilde ölçülebilmesi mümkündür.

 

Işın Çapı

LK-H008W 

LK-H027 

LK-H057 

LKH087 

LK-H157

 20 x 550µm

 25 x 1400µm

 50 x 2000µm

 70×2500µm

 120×4200µm

Metal Yüzeylerin Ölçümü

Fırçalanmış metal yüzey ölçümü

Fırçalanmış metal yüzeyler ve kauçuk yüzeyler gibi pürüzlü yüzeylerin etkisini en aza indirir. Bugüne kadar elde edilmiş en doğru ölçüm kapasitesine sahiptir.

LK-G5000 Serisinde kullanılan gelişmiş silindir lens sayesinde, geniş ışın ekseni alanın tamamını görür. Hedef sensör başlığına yakınlaşır ya da uzaklaşırsa görüntüde bozulma olmaz.

Parlak Yüzeyler

Parlak yüzeyler ve profil ölçümleri için en iyisidir.

Fokuslu Işın

Sınıfının en küçük ışın çapına sahip olduğu için (LK-H022 – ø25 μm), parlak yüzeylerden profillere kadar tüm hedefleri en yüksek doğruluk oranıyla okuyabilir.

Işın Çapı

LK-H008 

LK-H022 

 LK-H052

LK-H082 

LK-H152

 Ø20µm

 Ø25µm

Ø50µm

Ø70µm

Ø120µm

Mikroçip Pin Yüksekliği Ölçümü

Delta cut teknolojisi sayesinde optik filtreden dolayı oluşan bozulmanın etkisi en aza iner. Optik sistemdeki bu ve bunun gibi yenilikler sayesinde yalnızca RS-CMOS üzerine odaklanmakla kalmaz, hedef alana tam olarak odaklanır.  Bu sayede profiller üzerinde önceden mümkün olmayan yüksek hassasiyetli okuma yapılabilir.

Saydam Yüzeyler

Saydam/Aynalı yüzey ölçümü

Ayna Yansıması

LK-G5000 Serisi cam ya da ayna gibi yansıyan yüzeylerde kullanılmak üzere tasarlanmış başlıklara sahiptir. Bu başlıklar geniş ya da odaklı ışın seçenekleri ile yansıyan yüzeylerde yapılan ölçümler için idealdir.

Işın Çapı (Geniş Tip)

LK-H008W 

LK-H027K

LK-H057K

LKH087 + LK-F3

LK-H157 +LK-F2

 20 x 550µm

 25 x 1400µm

 50 x 2000µm

 70×2500µm

 120×4200µm

Işın Çapı (Nokta Tipi)

LK-H008 

LK-H022 

 LK-H052K

LK-H082 +LK-F3

LK-H152+LK-F2

 Ø20µm

 Ø25µm

Ø50µm

Ø70µm

Ø120µm

Dokunmatik Ekran Çevre Boşluğu Ölçümü

Bu özel başlıklarda bulunan optik sistem yüksek yansımaya sahip yüzeylerde maksimum çözünürlük elde etmek üzere tasarlanmıştır.  Alıcının gelişmiş özellikleri sayesinde 20 μm’a kadar olan boşlukların doğru şekilde ölçülebilmesi mümkündür.

Sensör Başlığı

Üstün öçme kpasitesi ile tüm ölçümlerde mükemmel performans

Yarısaydam Obje RPD* Algoritması

Lazer ışını nesnenin içine nüfuz ettiğinde yarısaydam obje dağınık yansımaya neden olur ve yansıyan ışık dalgasının açısı hafifçe genişler. RPD algoritması, genişleyen ışık dalgasının etkisini ortadan kaldırarak Real Peak’in tespit edilmesini sağlar.
*RPD=Real Peak Detect

 

Saydam Obje MULTI-ABLE KUMANDASI

Yansıyan ışığı algılayıp ayarlayarak lazer yoğunluğunu saydam objenin her katmanı için optimize eder. Ölçüm sırasında katmanlardaki yansımadan etkilenilmediği için yüksek doğruluk elde edilir.,

Çok Parlak Reçine CPC* ALGORİTMASI

Hedef yüzeyden yansıyan ışığın dalga açılarını birleştirerek daha yüksek çözünürlüklü ölçüm yapar. Dalgalardan biri yüksek yansımaya sahip yüzeyden, diğeri ise yüzeyin altından yansıyan ışıktan kaynaklanır.
*Merkez ve Pik (Peak) Birleşimi

İnce çizgili metal yüzey ölçümü

Klasik Modellere* Göre 2,3 Kat Daha Geniş Işın

Geniş alan ışını, zorlu hedef yüzeylerdeki dağınık yansıma ve çöküntülerin ortalamasını alarak doğru ölçüm yapmaya imkan sağlar.

* LK-G37 ve LK-H057 modelleri ile karşılaştırılmıştır.

Çok Küçük Hedef ve Şekillerin Ölçümü;

Çok İnce Işın Ø25 μm

Minimum Ø25 μm genişliğindeki çok ince ışın sayesinde çok küçük noktalar tam doğrulukla algılanır. Profil çıkarma için de uygundur.

Yansımalar için Geliştirilmiş Sensör Başlığı

KEYENCE sensör başlığı yansımalar için geliştirilmiştir ve yansımaya göre pozisyon alarak tam doğruluk sağlar. KEYENCE, doğrusallığı yüksek oranda arttırmak için ışık alıcı optik sistemi özel olarak tasarlamıştır. Bunun da ötesinde KEYENCE, aynasal yansıma için konumlandırılan sensör başlıkları ile hizalama ayarlamasını test ederek F.S özelliklerini %±0.02 sapma ile karşılar.

Hız (m/s) ve İvme (m/s2) Ölçümü

LK-G5000 Serisi hızını (m/s) ve ivmesini (m/s2) doğrudan ölçme özelliğine sahiptir. Ölçüm tipini seçmeniz yeterlidir:  “deplasman”, “hız” ya da “ivme”. Diferansiyel işleme devresi kumandanın içinde bulunduğundan, önceden ayrıca hesaplanan ölçümleri tek işlemde yapabilmek mümkündür. Temaslı sensör ile ölçülmesi zor olan hafif, kolay deforme olan ve yüksek sıcaklıktaki hedeflerin ölçümü için uygundur.

Kumanda: 3 Ölçme Seçeneği

Yan donanımlar ile bağlantı sağlamak ve görüntü biçimini ihtiyaca göre ayarlamak kolaylaştırıldı.

Kumanda : Harici ekran bağlantısı ile görüntüleme yapmak ve görüntü stilini ihtiyaca göre ayarlamak için çok kolay

1) Uzaktan Kumanda : Kumanda, operasyon/görüntüleme ünitelerinden 10 m uzağa yerleştirilebilir.

2) Direkt Kontrol : Dahili ekranlı kompakt kumandaya, ünite üzerindeki tuşlar kullanılarak doğrudan müdahale edilebilir.

3) Dokunmatik Ekran : Özel dokunmatik paneli sayesinde alınan ışık dalgalarını ve ölçülen değerleri ayarlamak ve görüntülemek kolaydır.

12 Sensör Başlığı/Network Kapasiteli

Ana kumandaya ekstra başlık ekleyerek, 12 ayrı başlığa kadar eş zamanlı ölçüm yapılabilir. CC-Link/DeviceNet™ ile uyumlu olduğu için diğer üreticilere ait birimlerin bulunduğu ağlara eklenebilir.

 

Pratik Hesaplama Fonksiyonu

Birden fazla başlık tarafından ölçülen değerleri anında hesaplayarak, önceden PLC ya da PC’ler ile yapılan karmaşık ölçümlerin kumandada yapılabilmesini sağlar.

PC ile Kolay Ayarlama ve Analiz

Büyük hedeflerin Ölçümü (Geniş Işın)

 

Parlak Hedeflerin Ölçümü (Odaklı Işın)

Saydam / Aynalı Hedeflerin Ölçümü (Aynasal Yansıma)

Teknik özellikler

Model

LK-G152

Reference distance

Diffuse reflection: 150 mm, specular reflection: 147.5 mm

Measurement range

Diffuse reflection: ± 40 mm, specular reflection: ± 39 mm * 1 * 2

light source

type

Red semiconductor laser

wavelength

655 nm (visible light)

output

Up to 0.95 mW

Spot diameter (at reference distance)

Approximately ø120 µm

Straightness

± 0.05% of FS (FS = ± 40 mm) * 1

Repeat accuracy

0.5 µm * 3

Sampling cycle

20/50/100/200/500/1,000 µs (6 steps variable)

LED display

Near the measurement center: Lights green, Inside the measurement range: Lights orange, Outside the measurement range: Flashes orange

Temperature characteristics

0.01% of FS / ℃ (FS = ± 40 mm)

Environmental resistance

Protective structure

IP67 (IEC60529)

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 5,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

mass

Approximately 290 g (including code)

* 1 Value when measuring our standard object (ceramic) in standard mode.
* 2 When the sampling period is 20 µs, it is -22 mm (NEAR side) to -40 mm (NEAR side) for diffuse reflection and -22 mm (NEAR side) to -39 mm (NEAR side) for specular reflection.
* 3 Value when our standard object (SUS) is measured at an average number of 4,096 times at a reference distance.

Model

LK-G3001 * 1

type

Separate type (English version) * 2

Head compatibility

Yes

Number of heads connected

Max 2 units

display

Minimum display unit

0.01 µm

Display range

± 9,999.99 mm to ± 9,999.99 µm (6 levels can be selected)

Display cycle

10 times / sec

Terminal block

Analog voltage output

± 10 V x 2 Output, output impedance 100 Ω

Analog current output

4 to 20 mA x 2 output, maximum load resistance 350 Ω

Timing input

No voltage input for OUT1

Reset input

Auto zero input

Laser remote interlock input

No voltage input

Judgment output

NPN open collector output for OUT1

Alarm output

NPN open collector output for OUT1 (NC)

Expansion connector

Timing input

No voltage input for OUT2

Reset input

Auto zero input

Program switching input

No voltage input x 3 inputs

Laser off input

No-voltage input for head A / head B

Judgment output

NPN open collector output for OUT2

Alarm output

NPN open collector output for OUT2 (NC)

binary

Binary output

Measurement data output (21 bit), OUT1 / OUT2 selectable, NPN open collector output

Strobe output

NPN open collector output

Binary selective output

Binary select input

No voltage input

RS-232C interface

Measurement data output and control input / output (baud rate can be selected up to 115,200 bit / s)

USB interface

USB Revision 2.0 full speed (USB1.1 compatible) compliant

Main functions

2OUT simultaneous measurement function, calculation function, averaging function, filter function, calibration function, measurement function, auto zero function, sampling cycle setting function,
mutual interference prevention function, data storage function, 8 program memory function, eco mode, ABLE setting function, measurement Object setting function,
ABLE tuning function, transparent object measurement surface selection function, statistical processing function, setting support software connection function, head installation selection function, etc.

Rated

Power-supply voltage

DC 24 V ± 10%, Ripple (PP) 10% or less

Maximum current consumption

When one head is connected: 500 mA or less / When two heads are connected: 600 mA or less

Environmental resistance

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

mass

About 370 g

* 1 The maximum rating of the NPN open collector is 50 mA (40 V or less) and the residual voltage is 1.0 V or less. The rating of the non-voltage input is ON voltage 1 V or less and OFF current 0.6 mA or less.
* 2 LK-G3001 can be used alone. The measured value can be displayed and the setting can be changed from the display panel (LK-GD500) or the setting support software (LK-H1W).

Model

LK-G3001P * 1

type

Separate type (PNP output type English version) * 2

Head compatibility

Yes

Number of heads connected

Max 2 units

display

Minimum display unit

0.01 µm

Display range

± 9,999.99 mm to ± 9,999.99 µm (6 levels can be selected)

Display cycle

10 times / sec

Terminal block

Analog voltage output

± 10 V x 2 Output, output impedance 100 Ω

Analog current output

4 to 20 mA x 2 output, maximum load resistance 350 Ω

Timing input

Voltage input for OUT1

Reset input

Auto zero input

Laser remote interlock input

No voltage input

Judgment output

PNP open collector output for OUT1

Alarm output

PNP open collector output for OUT1 (NC)

Expansion connector

Timing input

Voltage input for OUT2

Reset input

Auto zero input

Program switching input

Voltage input x 3 inputs

Laser off input

Voltage input for head A / head B

Judgment output

PNP open collector output for OUT2

Alarm output

PNP open collector output for OUT2 (NC)

binary

Binary output

Measurement data output (21 bit), OUT1 / OUT2 selectable, PNP open collector output

Strobe output

PNP open collector output

Binary selective output

Binary select input

Voltage input

RS-232C interface

Measurement data output and control input / output (baud rate can be selected up to 115,200 bit / s)

USB interface

USB Revision 2.0 full speed (USB1.1 compatible) compliant

Main functions

2OUT simultaneous measurement function, calculation function, averaging function, filter function, calibration function, measurement function, auto zero function, sampling cycle setting function,
mutual interference prevention function, data storage function, 8 program memory function, eco mode, ABLE setting function, measurement Object setting function,
ABLE tuning function, transparent object measurement surface selection function, statistical processing function, setting support software connection function, head installation selection function, etc.

Rated

Power-supply voltage

DC 24 V ± 10%, Ripple (PP) 10% or less

Maximum current consumption

When one head is connected: 500 mA or less / When two heads are connected: 600 mA or less

Environmental resistance

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

mass

About 370 g

* 1 PNP open collector output rating: maximum 50 mA (40 V or less), residual voltage 1.0 V or less
Voltage input rating: input maximum rating 26.4 V, ON voltage 10.2 V, OFF current 0.6 mA
* 2 LK-G3001P can be used alone I will. The measured value can be displayed and the setting can be changed from the display panel (LK-GD500) or the setting support software (LK-H1W).

Model

LK-G3001PV * 1

type

Integrated type (PNP output type English version)

Separate type

LK-G3001P / LK-GD500 * 2

Head compatibility

Yes

Number of heads connected

Max 2 units

display

Minimum display unit

0.01 µm

Display range

± 9,999.99 mm to ± 9,999.99 µm (6 levels can be selected)

Display cycle

10 times / sec

Terminal block

Analog voltage output

± 10 V x 2 Output, output impedance 100 Ω

Analog current output

4 to 20 mA x 2 output, maximum load resistance 350 Ω

Timing input

Voltage input for OUT1

Reset input

Auto zero input

Laser remote interlock input

No voltage input

Judgment output

PNP open collector output for OUT1

Alarm output

PNP open collector output for OUT1 (NC)

Expansion connector

Timing input

Voltage input for OUT2

Reset input

Auto zero input

Program switching input

Voltage input x 3 inputs

Laser off input

Voltage input for head A / head B

Judgment output

PNP open collector output for OUT2

Alarm output

PNP open collector output for OUT2 (NC)

binary

Binary output

Measurement data output (21 bit), OUT1 / OUT2 selectable, PNP open collector output

Strobe output

PNP open collector output

Binary selective output

Binary select input

Voltage input

RS-232C interface

Measurement data output and control input / output (baud rate can be selected up to 115,200 bit / s)

USB interface

USB Revision 2.0 full speed (USB1.1 compatible) compliant

Main functions

2OUT simultaneous measurement function, calculation function, averaging function, filter function, calibration function, measurement function, auto zero function, sampling cycle setting function,
mutual interference prevention function, data storage function, 8 program memory function, eco mode, ABLE setting function, measurement Object setting function,
ABLE tuning function, transparent object measurement surface selection function, statistical processing function, setting support software connection function, head installation selection function, etc.

Rated

Power-supply voltage

DC 24 V ± 10%, Ripple (PP) 10% or less

Maximum current consumption

When one head is connected: 500 mA or less / When two heads are connected: 600 mA or less

Environmental resistance

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

mass

About 480 g

* 1 PNP open collector output rating: maximum 50 mA (40 V or less), residual voltage 1.0 V or less
Voltage input rating: input maximum rating 26.4 V, ON voltage 10.2 V, OFF current 0.6 mA
* 2 LK-G3001P can be used alone I will. The measured value can be displayed and the setting can be changed from the display panel (LK-GD500) or the setting support software (LK-H1W).

Model

LK-G32

Reference distance

Diffuse reflection: 30 mm, specular reflection: 23.5 mm

Measurement range

Diffuse reflection: ± 5 mm, specular reflection: ± 4.5 mm * 1

light source

type

Red semiconductor laser

wavelength

655 nm (visible light), class 2 (JIS C6802)

output

Up to 0.95 mW

Spot diameter (at reference distance)

Approximately ø30 µm

Straightness

± 0.05% of FS (FS = ± 5 mm) * 2

Repeat accuracy

0.05 µm * 3

Sampling cycle

20/50/100/200/500/1,000 µs (6 steps variable)

LED display

Near the measurement center: Lights green, Inside the measurement range: Lights orange, Outside the measurement range: Flashes orange

Temperature characteristics

0.01% of FS / ℃ (FS = ± 5 mm)

Environmental resistance

Protective structure

IP67 (IEC60529)

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 10,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

mass

Approximately 280 g (including code)

* 1 When the sampling period is 20 µs, it is +1.8 mm (FAR side) to -5 mm (NEAR side) for diffuse reflection and +1.6 mm (FAR side) to -4.5 mm (NEAR side) for specular reflection.
* 2 Value when measuring our standard object (ceramic) in standard mode.
* 3 Value when our standard object (SUS) is measured at an average number of 4,096 times at a reference distance.

Model

LK-G407

Reference distance

Diffuse reflection: 400 mm, specular reflection: 398 mm

Measurement range

Diffuse reflection: ± 100 mm, specular reflection: ± 99 mm * 1 * 2

light source

type

Red semiconductor laser

wavelength

655 nm (visible light)

output

Up to 0.95 mW

Spot diameter (at reference distance)

Approximately 290 x 8,300 µm

Straightness

± 0.05% of FS (FS = ± 100 mm) * 1

Repeat accuracy

2 µm * 3

Sampling cycle

20/50/100/200/500/1,000 µs (6 steps variable)

LED display

Near the measurement center: Lights green, Inside the measurement range: Lights orange, Outside the measurement range: Flashes orange

Temperature characteristics

0.01% of FS / ℃ (FS = ± 100 mm)

Environmental resistance

Protective structure

IP67 (IEC60529)

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 5,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

mass

Approximately 380 g (including code)

* 1 Value when measuring our standard object (ceramic) in standard mode.
* 2 Measurement range when sampling period is 20 µs: -70 mm (NEAR side) to -100 mm (NEAR side) for diffuse reflection, -70 mm (NEAR side) to -99 mm (NEAR side) for specular reflection
* 3 Value when our standard object (SUS) is measured at a reference distance with an average number of 4,096 times.

Model

LK-G5001PV

type

Main controller

Separate type

LK-G5001P / LK-HD500

Head compatibility

Yes

Number of heads connected

Two

display

Minimum display unit

LK-HD500: 0.001 µm

Display range

LK-HD500: ± 999.999 µm to ± 9,999.99 mm (7 levels can be selected)

Display cycle

LK-HD500: 10 times / sec

Display interface

DISPLAY port

Either the display unit (LK-HD500) or the dedicated touch panel (LK-HD1000) can be connected.

LED display

LASER ON

Terminal block

Analog voltage output

± 10 V, output impedance 100 Ω

Analog current output

4 to 20 mA, maximum load resistance 350 Ω

Number of analog outputs

2

Timing 1 input

Voltage input * 1

Reset 1 input

Auto zero 1 input

Laser control input

Voltage input * 2

Laser remote input

No voltage input

Alarm output

PNP open collector output

Comprehensive judgment output

Expansion connector

Timing input

Voltage input

Reset input

Auto zero input

Program switching input

Binary select input

Alarm output

PNP open collector output

Judgment output

Binary output

RS-232C interface

Baud rate 9,600 to 115,200 bps, data length 8 bits, stop bit 1 bit, no parity / even / odd

USB interface

USB Revision 2.0 high speed compliant * 3

Ethernet interface

100Base-TX / 10Base-T * 4

EtherNet / IP TM interface

Cyclic communication (Implicit message) Message communication (Explicit message),
UCMM and Class3 Number of connections 32 Conformance test Version.CT14 supported * 5

PLC link

Compatible with Mitsubishi Electric MELSEC iQ-R series, iQ-F series, Q series, L series, FX series Exclusive use with
EtherNet / IP TM , CC-Link, DeviceNet TM

Expansion unit connector

Up to 10 head expansion units can be connected to one main controller

Expansion unit connector

CC-Link Unit (LK-CC100) DeviceNet TM units (LK-DN100)
can be connected to one or

Power supply

Power-supply voltage

DC 24 V ± 10%

Maximum current consumption

When 1 head is connected: 0.6 A or less / When 12 heads are connected: 3.5 A or less

Environmental resistance

Operating ambient temperature

Number of head expansion units 1 or less: 0 to + 50 ° C
Number of head expansion units 2 or more: 0 to + 40 ° C

Operating ambient humidity

35-85% RH (no condensation)

mass

About 600 g

* 1 Works for all OUT numbers set for synchronization.
* 2 When a laser class 3B sensor head is connected, use the key switch to input (the laser turns on when short-circuited).
When a laser class 1/2 / 3R sensor head is connected, the laser is turned on when open and the laser is turned off when short-circuited.
* 3 USB Revision1.1, USB Revision2.0 When connected to a full-speed computer, the data update cycle may be delayed.
* 4 Make the Ethernet connection 1: 1 connection to the personal computer, or local connection only to the personal computer and the LK-G5000 series.
* 5 The EtherNet / IP TM interface cannot be used when the CC-Link unit or DeviceNet TM unit is installed . EtherNet / IP TM is supported from controllers shipped after March 23, 2018.

Model

LK-G507

Reference distance

Diffuse reflection: 500 mm, specular reflection: 497.5 mm

Measurement range

Diffuse reflection: -250 to +500 mm, specular reflection: -249 to +498 mm * 1

light source

type

Red semiconductor laser

wavelength

655 nm (visible light)

output

Up to 0.95 mW

Spot diameter (at reference distance)

Approximately 300 x 9,500 µm

Repeat accuracy

2 µm * 2

Sampling cycle

20/50/100/200/500/1,000 µs (6 steps variable)

LED display

Near the measurement center: Lights green, Inside the measurement range: Lights orange, Outside the measurement range: Flashes orange

Temperature characteristics

0.01% of FS / ℃ (FS = ± 250 mm)

Environmental resistance

Protective structure

IP67 (IEC60529)

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 5,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

mass

Approximately 380 g (including code)

* 1 Value when measuring our standard object (ceramic) in standard mode.
When the sampling period is 20 µs, the diffuse reflection is from -230 mm (NEAR side) to -250 mm (NEAR side), when the specular reflection is from -230 mm (NEAR side) to -249 mm (NEAR side), and when the
sampling period is 50 µs. Diffuse reflection is -125 mm (NEAR side) to -250 mm (NEAR side), and specular reflection is -125 mm (NEAR side) to -249 mm (NEAR side).
* 2 Value when our standard object (SUS) is measured at an average number of 4,096 times at a reference distance.

Model

LK-G82

Reference distance

Diffuse reflection: 80 mm, specular reflection: 75.2 mm

Measurement range

Diffuse reflection: ± 15 mm, specular reflection: ± 14 mm * 1 * 2

light source

type

Red semiconductor laser

wavelength

655 nm (visible light)

output

Up to 0.95 mW

Spot diameter (at reference distance)

Approximately ø70 µm

Straightness

± 0.05% of FS (FS = ± 15 mm) * 1

Repeat accuracy

0.2 µm * 3

Sampling cycle

20/50/100/200/500/1,000 µs (6 steps variable)

LED display

Near the measurement center: Lights green, Inside the measurement range: Lights orange, Outside the measurement range: Flashes orange

Temperature characteristics

0.01% of FS / ℃ (FS = ± 15 mm)

Environmental resistance

Protective structure

IP67 (IEC60529)

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 10,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

mass

Approximately 380 g (including code)

* 1 Value when measuring our standard object (ceramic) in standard mode.
* 2 Measurement range when sampling period is 20 µs: -9 mm (NEAR side) to -15 mm (NEAR side) for diffuse reflection, -8.7 mm (NEAR side) to -14 mm (NEAR side) for specular reflection
* 3 Value when our standard object (SUS) is measured at a reference distance with an average number of 4,096 times.

Model

LK-G87

Reference distance

Diffuse reflection: 80 mm, specular reflection: 75.2 mm

Measurement range

Diffuse reflection: ± 15 mm, specular reflection: ± 14 mm * 1 * 2

light source

type

Red semiconductor laser

wavelength

655 nm (visible light)

output

Up to 0.95 mW

Spot diameter (at reference distance)

Approximately 70 x 1,100 µm

Straightness

± 0.05% of FS (FS = ± 15 mm) * 1

Repeat accuracy

0.2 µm * 3

Sampling cycle

20/50/100/200/500/1,000 µs (6 steps variable)

LED display

Near the measurement center: Lights green, Inside the measurement range: Lights orange, Outside the measurement range: Flashes orange

Temperature characteristics

0.01% of FS / ℃ (FS = ± 15 mm)

Environmental resistance

Protective structure

IP67 (IEC60529)

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 10,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

mass

Approximately 380 g (including code)

* 1 Value when measuring our standard object (ceramic) in standard mode.
* 2 Measurement range when sampling period is 20 µs: -9 mm (NEAR side) to -15 mm (NEAR side) for diffuse reflection, -8.7 mm (NEAR side) to -14 mm (NEAR side) for specular reflection
* 3 Value when our standard object (SUS) is measured at a reference distance with an average number of 4,096 times.

Model

LK-GC10

cable length

10 m

mass

Approximately 750 g (including code)

Model

LK-GC2

cable length

2 m

mass

Approximately 200 g (including code)

Model

LK-GC5

cable length

5 m

mass

Approximately 400 g (including code)

Model

LK-GD500

type

Display panel
compatible model: LK-G3000, LK-G3000P

display

Minimum display unit

0.01µm

Display range

± 9999.99 mm to ± 9999.99 µm (6 levels can be selected)

Display cycle

10 times / sec

mass

About 60 g

Model

LK-H027

Installation mode

Diffuse reflection

Reference distance

20mm

Measurement range

± 3mm * 1

light source

type

Red semiconductor laser

wavelength

655nm

Laser class (JIS C6802)

Class 2 laser products * 2

output

0.95mW

Spot diameter (at reference distance)

25µm x 1400µm

Straightness

± 0.02% of F.S. (FS = 6mm) * 3

Repeat accuracy

0.02 µm (0.01 µm) * 4

Sampling cycle

2.55 / 5/10/20/50/100/200/500 / 1000µs (9-step variable)

Temperature characteristics

0.01% of F.S./ ℃ (FS = 6mm)

Environmental resistance

Protective structure

IP67

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 10,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

aluminum die cast

mass

About 230 g

* 1 The measurement range is when the sampling period is 20 µs or more.
* 2 Please contact us for class 3B type sensor heads.
* 3 This is the value when our standard object (white diffuse object / LK-H008 / LK-H008W only metal mirror surface object) is measured in the standard mode.
* 4 This is the value when our standard object (white diffuse object / LK-H008 / LK-H008W only metal mirror surface object) is measured at an average number of 16384 times at a reference distance.
Figures in parentheses are typical examples of measurements taken with an average number of 65536 times and a sampling period of 200 µs.

Model

LK-H057

Installation mode

Diffuse reflection

Reference distance

50mm

Measurement range

± 10mm * 1

light source

type

Red semiconductor laser

wavelength

655nm

Laser class (JIS C6802)

Class 2 laser products * 2

output

0.95mW

Spot diameter (at reference distance)

50µm x 2000µm

Straightness

± 0.02% of F.S. (FS = 20mm) * 3

Repeat accuracy

0.025 µm * 4

Sampling cycle

2.55 / 5/10/20/50/100/200/500 / 1000µs (9-step variable)

Temperature characteristics

0.01% of F.S./ ℃ (FS = 20 mm)

Environmental resistance

Protective structure

IP67

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 10,000 lux or less

Operating ambient temperature

0 to + 50 ° C

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

aluminum die cast

mass

About 260 g

* 1 The measurement range is when the sampling period is 20 µs or more.
* 2 Please contact us for class 3B type sensor heads.
* 3 This is the value when our standard object (white diffuse object / LK-H008 / LK-H008W only metal mirror surface object) is measured in the standard mode.
* 4 This is the value when our standard object (white diffuse object / LK-H008 / LK-H008W only metal mirror surface object) is measured at an average number of 16384 times at a reference distance.
Figures in parentheses are typical examples of measurements taken with an average number of 65536 times and a sampling period of 200 µs.

Model

LK-H157

Installation mode

Diffuse / specular * 1

Reference distance

Diffuse reflection: 150mm
Specular reflection: 147.5mm

Measurement range

Diffuse reflection: ± 40mm
Specular reflection: -39.5mm to +24.4mm * 2

light source

type

Red semiconductor laser

wavelength

655nm

Laser class (JIS C6802)

Class 2 laser products * 3

output

0.95mW

Spot diameter (at reference distance)

120µm × 4200µm

Straightness

± 0.02% of F.S. (FS = 80mm) * 4

Repeat accuracy

0.25 µm * 5

Sampling cycle

2.55 / 5/10/20/50/100/200/500 / 1000µs (9-step variable)

Temperature characteristics

0.01% of F.S./ ℃ (FS = 80 mm)

Environmental resistance

Protective structure

IP67

Ambient illuminance used

Incandescent lamp / fluorescent lamp: 5,000 lux or less

Operating ambient temperature

0 to + 50 ° C * 6

Operating ambient humidity

35-85% RH (no condensation)

Vibration resistant

10-55 Hz, double amplitude 1.5 mm, X, Y, Z 2 hours in each direction

Material

aluminum die cast

mass

About 300 g

* 1 Use the dimming filter shown on the right for transparent / mirror surface measurement. LK-H08 □: LK-F3, LK-H15 □: LK-F2
* 2 The measurement range is when the sampling period is 20 µs or more.
* 3 Please contact us for class 3B type sensor heads.
* 4 This is the value when our standard object (white diffuse object / LK-H008 / LK-H008W only metal mirror surface object) is measured in the standard mode.
* 5 This is the value when our standard object (white diffuse object / LK-H008 / LK-H008W only metal mirror surface object) is measured at an average number of 16384 times at a reference distance.
Figures in parentheses are typical examples of measurements taken with an average number of 65536 times and a sampling period of 200 µs.
* 6 If the ambient temperature is 40 ° C or higher, it must be attached to a metal plate for use.

İnsanların web sitemizi nasıl kullandıklarını analiz ederek, deneyiminizi ve hizmetlerimizi daha iyi hale getirmek için kendi çerezlerimizi ve üçüncü taraf çerezleri kullanıyoruz. Web sitesini kullanmaya devam ettiğinizde bunların kullanımını kabul ettiğinizi anlıyoruz. Çerez Politikamız hakkında daha fazla bilgi için burayı tıklayın.

2D Profilers give width, height, and volume of sealant beads inline without touching a part.

2D/3D Laser Profiler
LJ-X8000 series

Conventionally, a vision sensor was used for OK/NG judgment based on the area. Since the LJ-X8000 Series can measure the volume and position of paste application, it can reduce material costs and support higher component densities.

2D/3D Laser Profiler
LJ-X8000 series

Check the tilt of the elements after bonding. The CL-3000 Series uses the multi-color confocal method that enables coaxial measurement. No matter whether the target surfaces are specular or rough, they can be measured in the same setting, which achieves easy and highly accurate inspection.

Ultra Confocal Displacement Sensor
CL-3000 series

High-speed sensors can measure runout of brake discs, regardless of surface finish.

Confocal Displacement Sensor
CL-3000 series

Measure the extent of foil vibration just before the slit. Even if the target is tilted due to vibration, the good angle characteristics of the CL Series enable stable measurement.

Confocal Displacement Sensor
CL-3000 series

A sensor is placed above and below a target to measure the thickness of anything in-between. This non-contact method can be used for measuring the thickness of any material and can be used in process or for offline inspection.

Confocal Displacement Sensor
CL-3000 series
-

Ultra-compact ø8 mm heads make it possible to install multiple heads in narrow spaces. This reduces the amount of work spent designing equipment and the number of parts that need to be purchased to measure multiple points in close proximity.

Confocal Displacement Sensor
CL-3000 series

Check step heights on machined parts without influence from oil or other surface contamination.

High-Accuracy Digital Contact Sensor
GT2 series

Measure many points on an engine with a multi-point laser system for accurate characterization of engine vibration. With ultra-highspeed sensors, even the smallest vibrations can be detected.

Ultra High-Speed/High-Accuracy Laser Displacement Sensor
LK-G5000 series

Measure the position and edge flutter of a belt with two 2D laser profile sensors for stable measurement.

2D/3D Laser Profiler
LJ-X8000 series

Residual vibration measurement is used to determine how much a robot shakes after stopping. When working with a welding torch or other tool, the measurement location may not always have a flat surface. Using a 2D laser profiler enables accurate measurement on a wide range of surface shapes.

2D/3D Laser Profiler
LJ-X8000 series

Opposing 2D profilers can scan multiple points of thickness over a part. This allows stable thickness measurement even on rough surfaces.

2D/3D Laser Profiler
LJ-X8000 series

High-speed thrubeam sensors can measure runout and ovality of rotors accurately and repeatably.

High-speed optical micrometer
LS-9000 series

Measure roller runout using confocal sensors for high stability on reflective surfaces.

Confocal Displacement Sensor
CL-3000 series

Thrubeam micrometers allow for high-speed measurement of wire OD without being affected by vibration.

High-speed optical micrometer
LS-9000 series

2D thrubeam sensors can measure hole diameter after stamping inline.

Telecentric Measurement System
TM-X5000 series

The Telecentric Measurement System uses 2D images of a target's silhouette to measure diameter. Target misalignment or tilt is automatically corrected for, making it simple to get accurate measurement without perfect fixturing.

Telecentric Measurement System
TM-X5000 series

Compressible or rough surfaces can be accurately measured using the 2D image generated by the Telecentric Measurement System. Implementing non-contact measurement eliminates error due to part deformation and any variation in diameter due to surface texture can be averaged over to stabilize results.

Telecentric Measurement System
TM-X5000 series

Compressible or rough surfaces can be accurately measured using the 2D image generated by the Telecentric Measurement System. Implementing non-contact measurement eliminates error due to part deformation and any variation in diameter due to surface texture can be averaged over to stabilize results.

Telecentric Measurement System
TM-X5000 series

Using 2D measurement systems makes it possible to measure the minimum and maximum diameter on a target from a single captured image. The TM-X Series works by capturing the silhouette of a target using a telecentric optical system, so it can accurately measure objects of any material (including clear vials).

Telecentric Measurement System
TM-X5000 series

With an exposure time of just 100 µs, the Telecentric Measurement System can capture clear images of targets moving at high speed. This makes it an ideal solution for accurately measuring diameter inline.

Telecentric Measurement System
TM-X5000 series

With small sensor heads and a mirror fixture, confocal sensors can give an accurate measurement of pipe ID.

Confocal Displacement Sensor
CL-3000 series

High-speed laser displacement sensors can check for valve float without touching the valve head.

Ultra High-Speed/High-Accuracy Laser Displacement Sensor
LK-G5000 series

Measure fine details on touch panels regardless of surface finish with confocal sensors. With a beam spot of 3.5μm, even the smallest features can be measured.

Confocal Displacement Sensor
CL-3000 series

Check outer diameter on machined parts without influence from oil or other surface contamination.

High-Accuracy Digital Contact Sensor
GT2 series

High-speed laser displacement sensors can check for valve float without touching the valve head.

Ultra Confocal Displacement Sensor
CL-3000 series

Profile tire treads and sidewalls with multiple 2D laser profilers.

2D/3D Laser Profiler
LJ-X8000 series

Inspect for lamination misalignment after winding. With a minimum X-resolution of 2.5 μm 0.000098", the LJ-X8000 Series accurately measures the profile of each electrode.

2D/3D Laser Profiler
LJ-X8000 series

Provide feedback about disconnected locations in electrodes before lamination. Accurately acquire the profile of electrode terminals to perform high-accuracy inspection of edge locations.

2D/3D Laser Profiler
LJ-X8000 series

Measure the profile of a wafer edge. By selecting one of the inspection tools such as Height Difference/Width or Angle, users can start measurement easily. The high-resolution image capturing using 3200 points/profile achieves highly accurate profile measurement that was impossible with conventional methods.

2D/3D Laser Profiler
LJ-X8000 series

Film curvature and wrinkling measurements are performed using a blue laser with a maximum width of 720 mm. Measurement is possible even for transparent targets thanks to the wide dynamic range of the CMOS sensor.

2D/3D Laser Profiler
LJ-X8000 series

Measure the step height of features on a wafer after etching. With 3D interferometry, mirrored surfaces can be measured accurately.

3D Interference Measurement Sensor
WI-5000 series

Unlike triangulation sensors, interferometers can measure small parts in confined spaces without blind spots or unstable data.

3D Interference Measurement Sensor
WI-5000 series

Using 2D thrubeam sensors, medical balloons can be inspected inline at high-speed.

Telecentric Measurement System
TM-X5000 series

Measure small part dimensions inline with pattern projection measurement heads. Projection from both sides reduces dead zones.

Inline 3D Inspection
3D Vision series

With two thrubeam micrometers installed on either side of a film, we can get a width measurement and give film position, regardless of color or material.

High-speed optical micrometer
LS-9000 series

2D thrubeam sensors can measure the step height between a roller and a sheet to get a thickness measurement. Additionally, A second sensor can be added to get a width measurement.

Telecentric Measurement System
TM-X5000 series

A displacement sensor with an extremely small beam spot of just 3.5 µm can be used for accurate profile measurements of roughness and subtle shapes. 3D shape measurements are also possible through detailed scanning synchronized with the X-Y stage. Measurements with impressive angle characteristics are possible not only for opaque targets but also transparent targets and 3D shapes with mirrored surfaces.

Confocal Displacement Sensor
CL-3000 series

Confocal sensors do not have the dead zones characteristic of triangulation sensors, and can therefore measure into smaller and deeper holes more reliably.

Confocal Displacement Sensor
CL-3000 series

Measure the height of the equipment when adhesive is applied to glass. Utilizing the multi-colour confocal method measurement principle enables high-precision measurement whether the glass is transparent or opaque.

Confocal Displacement Sensor
CL-3000 series

2D Profilers can measure width, height, and volume of sealant beads inline, regardless of surface finish or color.

2D/3D Laser Profiler
LJ-X8000 series

Detect burrs arising on terminals after electrode slitting. With ultra-high-resolution 3200 points/profile measurement, the LJ-X8000 Series produces stable detection even for minute burrs.

2D/3D Laser Profiler
LJ-X8000 series

Profile measurement can be continuously performed on captured 3D shapes. This allows pass/fail criteria to be applied to maximum and minimum values over an area or period of time, making it possible to catch small defects in continuous processes.

2D/3D Laser Profiler
LJ-X8000 series

Free-form planes allow the system to pick up on deviations from the typical contour of a surface.This makes stable defect detection possible, even for targets with complex shapes.

2D/3D Laser Profiler
LJ-X8000 series

Highly accurate measurements can be made even when measuring targets with height differences or where the distance from the target to the camera could vary.

2D/3D Laser Profiler
LJ-X8000 series

2D laser displacement sensors can measure both width and height, allowing for panel gaps to be accurately measured, regardless of the surface finish or color.

2D/3D Laser Profiler
LJ-X8000 series

Detect chipping or dents in laser welded beads using 3D laser profilers. The measurement is unaffected by color or gloss of the weld, making inspection results stable through glare or bead shape variation.

2D/3D Laser Profiler
LJ-X8000 series

Using thrubeam sensors, roller position can be accurately measured at high line speeds.

High-speed optical micrometer
LS-9000 series

Targets with multiple materials can be captured in a single profile, allowing measurements to be made between glass and metal surfaces. The LJ-X Series is equipped to handle reflectances ten times higher than conventional products.

2D/3D Laser Profiler
LJ-X8000 series

For targets with different diameters, conventional vision systems often have a hard time focusing on the larger and smaller diameter areas at the same time. Measuring the height of the dents with a laser profiler makes it possible to inspect the whole surface at once.

2D/3D Laser Profiler
LJ-X8000 series

Measure the position and projection of connector terminals simultaneously. Conventionally, two measurement steps were required using an image processing system and a contact sensor. The LJ-X8000 Series can perform both inspections simultaneously. This achieves cost reduction by reducing the amount of installed equipment.

2D/3D Laser Profiler
LJ-X8000 series

3D inspection allows users to accurately detect whether components are properly seated in the assembly or if elements are tilted. Using a KEYENCE 2D/3D laser profiler with a blue laser ensures stable measurement, even for targets with varying materials.

2D/3D Laser Profiler
LJ-X8000 series

Robot teaching is used to ensure tools are set in the specified position. The 2D Telecentric Measurement System enables precise position feedback for end tools and other axial targets.

Telecentric Measurement System
TM-X5000 series

The laser profiler's wide field of view makes it possible to inspect multiple targets traveling on a conveyor belt together. 3D position correction can be used to identify and inspect each cookie within the measurement range, enabling accurate sorting to improve quality and eliminate waste.

2D/3D Laser Profiler
LJ-X8000 series

Measure the flatness of the terminals of power modules. The target is detected by its surface and the flatness is measured based on the reference plane calculated with the least squares fitting method. The errors caused by the tilted positions of targets can be canceled, which ensures accurate inspection.

2D/3D Laser Profiler
LJ-X8000 series

Angled mirrors can be used for measurement where installation space is limited. This setup enables position detection of tangent circle coordinates or intersection point coordinates as well as simultaneous shape and dimension verification for wafer notches.

Telecentric Measurement System
TM-X5000 series

Inspect motor height after powder welding using the LJ-X8000 Series. The 3D laser profiler provides reliable 100% inspection with its high speed and measurement stability.

2D/3D Laser Profiler
LJ-X8000 series

Measure transparent films and coatings with a single displacement sensor. Confocal sensors give an accurate thickness measurement from one side of transparent targets.

Confocal Displacement Sensor
CL-3000 series

In-line thickness measurements can be altered by roller eccentricity, wrinkles, or tension in the sheet. Up to 6 measurement points and 4 layers of clear film can be measured with a single controller.

Confocal Displacement Sensor
CL-3000 series

2D Profilers can measure width, height, and volume of sealant beads inline, regardless of surface finish or color.

2D/3D Laser Profiler
LJ-X8000 series

Check for press fit failure with contact displacement sensors.

High-Accuracy Digital Contact Sensor
GT2 series

Detect burrs arising on terminals after electrode slitting. With ultra-high-resolution 3200 points/profile measurement, the LJ-X8000 Series produces stable detection even for minute burrs.

2D/3D Laser Profiler
LJ-X8000 series

Profile measurement can be continuously performed on captured 3D shapes. This allows pass/fail criteria to be applied to maximum and minimum values over an area or period of time, making it possible to catch small defects in continuous processes.

2D/3D Laser Profiler
LJ-X8000 series

Free-form planes allow the system to pick up on deviations from the typical contour of a surface.This makes stable defect detection possible, even for targets with complex shapes.

2D/3D Laser Profiler
LJ-X8000 series

Highly accurate measurements can be made even when measuring targets with height differences or where the distance from the target to the camera could vary.

2D/3D Laser Profiler
LJ-X8000 series

2D Thrubeam sensors allow high-speed dimensional inspections to be taken on the silhouette of a part.

Telecentric Measurement System
TM-X5000 series

Target positioning is used to ensure the next process is performed accurately. Laser profilers provide stable position feedback anywhere in the measurement range, regardless of target material, color, or size.

2D/3D Laser Profiler
LJ-X8000 series

Detect chipping or dents in laser welded beads using 3D laser profilers. The measurement is unaffected by color or gloss of the weld, making inspection results stable through glare or bead shape variation.

2D/3D Laser Profiler
LJ-X8000 series

Targets with multiple materials can be captured in a single profile, allowing measurements to be made between glass and metal surfaces. The LJ-X Series is equipped to handle reflectances ten times higher than conventional products.

2D/3D Laser Profiler
LJ-X8000 series

For targets with different diameters, conventional vision systems often have a hard time focusing on the larger and smaller diameter areas at the same time. Measuring the height of the dents with a laser profiler makes it possible to inspect the whole surface at once.

2D/3D Laser Profiler
LJ-X8000 series

3D inspection allows users to accurately detect whether components are properly seated in the assembly or if elements are tilted. Using a KEYENCE 2D/3D laser profiler with a blue laser ensures stable measurement, even for targets with varying materials.

2D/3D Laser Profiler
LJ-X8000 series